| View previous topic :: View next topic |
| Author |
Message |
robertwinter
Site Admin
Joined: 02 Aug 2005
Posts: 298
Location: Los Angeles
|
 Posted: Fri Oct 28, 2005 8:44 pm Post subject: Backbox wiring picture |
 |
|
Kati just sent me this picture - looks as though the backbox interboard wiring is coming together quite nicely.
_________________
Robert
-----
http://www.robertwinter.com
BBB #74 |
|
| Back to top |
|
 |
harrrrrrr
Joined: 02 Aug 2005
Posts: 136
|
| Posted: Sat Oct 29, 2005 6:59 am Post subject: |
|
|
woo hoo love them photos...
thanks.
_________________
No. 7  arrrrrrr |
|
| Back to top |
|
|
Bertl
Joined: 02 Aug 2005
Posts: 187
Location: Vienna/Austria
|
| Posted: Sat Oct 29, 2005 12:02 pm Post subject: |
|
|
I love such pictures!
Thx a lot!
Brgds
Norbert |
|
| Back to top |
|
|
Swann
Joined: 02 Aug 2005
Posts: 108
Location: Stockholm, Sweden
|
| Posted: Sat Oct 29, 2005 1:42 pm Post subject: |
|
|
Thanx a bunch for the backbox picture! Just waiting for the one where the previously talked about backbox flashers are mounted too! 
_________________
BBB #79 has arrived here in Stockholm, Sweden! |
|
| Back to top |
|
|
BBB94
Joined: 02 Aug 2005
Posts: 407
Location: WI, USA
|
| Posted: Sat Oct 29, 2005 4:29 pm Post subject: |
|
|
| Man, is there anything about these machines that is not cool and or beautiful? Thanks for the pic. |
|
| Back to top |
|
|
sellenoff
Joined: 07 Aug 2005
Posts: 101
|
| Posted: Sun Oct 30, 2005 8:21 pm Post subject: |
|
|
Love the pic!!
Is it more, or does the switches relay board seem out of place at the bottom of the head. Seems that when you mount the front panel with the DMD and it's controller board that those will touch each other, or at the very least, be crammed up against each other, which is not a good thing. I would have thought it might mount on the top left side of the head.
Of course, I am sure they are following the layout of the machine that Gene bought, but it just seems like an usual spot for that board when it's possible to touch the dmd boards which would sit in front of it when mounted..
Am I crazy?
-Steve |
|
| Back to top |
|
|
Bertl
Joined: 02 Aug 2005
Posts: 187
Location: Vienna/Austria
|
| Posted: Sun Oct 30, 2005 11:18 pm Post subject: |
|
|
@sellenoff
The boards in the backbox are situated like in Pinball Magic and Airborne, so it's ok.
Brgds
Norbert |
|
| Back to top |
|
|
sellenoff
Joined: 07 Aug 2005
Posts: 101
|
| Posted: Mon Oct 31, 2005 7:33 am Post subject: |
|
|
Thanks for the confirmation, although I was more questioning Capcom's design choice, rather than assuming it a mistake by IPB, since I assumed they were using the BBB proto as a guide.
I wasn't totally sure though, so I"m glad you cleared it up.
So am I the only one who thinks it seems like an odd choice for Capcom to use?
| Bertl wrote: | @sellenoff
The boards in the backbox are situated like in Pinball Magic and Airborne, so it's ok.
Brgds
Norbert |
|
|
| Back to top |
|
|
BigBangJoe
Joined: 02 Aug 2005
Posts: 134
Location: Gent, Belgium
|
| Posted: Mon Oct 31, 2005 4:15 pm Post subject: |
|
|
| sellenoff wrote: | Is it more, or does the switches relay board seem out of place at the bottom of the head. Seems that when you mount the front panel with the DMD and it's controller board that those will touch each other, or at the very least, be crammed up against each other, which is not a good thing. I would have thought it might mount on the top left side of the head.
|
I have checked my Airborne, and there is a gap of at least 3 cm (a good inch) between any component at the back of the DMD and the boards in the backbox. There's no risk at all that they would touch each other. |
|
| Back to top |
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
